Zjednodušený výpočet průhybu segmentu ložiska
Loading...
Date
Authors
Janiš, Tomáš
ORCID
Advisor
Referee
Mark
C
Journal Title
Journal ISSN
Volume Title
Publisher
Vysoké učení technické v Brně. Fakulta strojního inženýrství
Abstract
Předložená bakalářská práce se zabývá výpočtem průhybu segmentu hydrodynamického radiálního ložiska s naklápěcími segmenty. Tento typ ložiska je popsán svými charakteristikami, které se určují pomocí simulací. Znalost těchto charakteristik je důležitá pro predikování chování ložisek v provozu a pro návrh zařízení využívající tyto ložiska. Charakteristiky ložiska jsou silně závislé na tloušťce mazacího filmu. Ta je ve skutečnosti velmi tenká, a proto ji ovlivňuje i sebemenší průhyb segmentu. Tato práce se proto zabývá výpočtem průhybu segmentů. Díky tomuto výpočtu je následně možné vliv deformace segmentů zahrnout do navazujících simulací pro určení charakteristik ložiska. Díky zahrnutí tohoto vlivu dojde ke zpřesnění simulací. Z tohoto důvodu je vytvořen výpočetní model průhybu segmentu ložiska. Tento model vychází z diferenciální rovnice průhybové čáry za předpokladu malých deformací. V tomto výpočtu jsou zahrnuty teplotní účinky způsobené zahříváním maziva a tlakové účinky způsobené zatížením segmentu ložiska. Výsledky průhybu od těchto zatížení jsou nadále porovnány s výsledky získané díky metodě konečných prvků. Při tomto porovnání nebyla dosažena požadovaná shoda.
The presented bachelor thesis deals with the calculation of deflection of a pad of a hydrodynamic radial bearing with tilting pads. This type of bearing is described by its characteristics, which are determined by means of simulations. Knowledge of these characteristics is important for predicting the behaviour of bearings in service and for the design of equipment using these bearings. The bearing characteristics are strongly dependent on the thickness of the lubricating film. This is in fact very thin and is therefore affected by the slightest deflection of the pad. This paper therefore deals with the calculation of pad deflection. With this calculation, the effect of pad deflection can then be included in downstream simulations to determine the bearing characteristics. The inclusion of this effect results in more accurate simulations. For this reason, a computational model of bearing pad deflection is developed. This model is based on the differential equation of the deflection line assuming small deformations. The temperature effects due to lubricant heating and the pressure effects due to bearing pad loading are included in this calculation. The deflection results from these loads are further compared with the results obtained by the finite element method. This comparison did not achieve the required compliance.
The presented bachelor thesis deals with the calculation of deflection of a pad of a hydrodynamic radial bearing with tilting pads. This type of bearing is described by its characteristics, which are determined by means of simulations. Knowledge of these characteristics is important for predicting the behaviour of bearings in service and for the design of equipment using these bearings. The bearing characteristics are strongly dependent on the thickness of the lubricating film. This is in fact very thin and is therefore affected by the slightest deflection of the pad. This paper therefore deals with the calculation of pad deflection. With this calculation, the effect of pad deflection can then be included in downstream simulations to determine the bearing characteristics. The inclusion of this effect results in more accurate simulations. For this reason, a computational model of bearing pad deflection is developed. This model is based on the differential equation of the deflection line assuming small deformations. The temperature effects due to lubricant heating and the pressure effects due to bearing pad loading are included in this calculation. The deflection results from these loads are further compared with the results obtained by the finite element method. This comparison did not achieve the required compliance.
Description
Citation
JANIŠ, T. Zjednodušený výpočet průhybu segmentu ložiska [online]. Brno: Vysoké učení technické v Brně. Fakulta strojního inženýrství. 2024.
Document type
Document version
Date of access to the full text
Language of document
cs
Study field
Základy strojního inženýrství
Comittee
Ing. Lubomír Junek, Ph.D. (předseda)
doc. Ing. Tomáš Návrat, Ph.D. (místopředseda)
Ing. Petr Marcián, Ph.D. (člen)
Ing. Oldřich Ševeček, Ph.D. (člen)
doc. Ing. František Šebek, Ph.D. (člen)
Ing. Petr Vosynek, Ph.D. (člen)
Ing. Dávid Halabuk, Ph.D. (člen)
Date of acceptance
2024-06-17
Defence
Během obhajoby student nejprve prezentoval svou bakalářskou práci, dále byly přečteny posudky a student poté odpovídal na dotazy oponenta. Následně byly členy komise položeny tyto otázky:
Můžete vaši využitou metodu použít i pro uložení s ložisky? Co si představujete pod pojmem přesnost výpočtu? Za předpokladu, že k výpočtu použijete dvě různé metody, jak určíte, která metoda je přesnější? Co nezahrnuje konečnoprvkový model ložiska oproti realitě? Jaká omezení má výpočtový model ložiska? Popište zatížení ložiska od teploty?
Na závěr byla obhajoba závěrečné práce ohodnocena známkou C – dobrá.
Result of defence
práce byla úspěšně obhájena
Document licence
Standardní licenční smlouva - přístup k plnému textu bez omezení