Návrh technologie výroby držáku senzoru
Loading...
Date
Authors
Horáček, Jonáš
ORCID
Advisor
Referee
Mark
A
Journal Title
Journal ISSN
Volume Title
Publisher
Vysoké učení technické v Brně. Fakulta strojního inženýrství
Abstract
Předkládaná diplomová práce je zaměřena na návrh technologie výroby držáku z polykarbonátu, který bude sloužit pro uchycení pohybových a hladinových senzorů na stěny obytných jednotek. Na základě požadavků a charakteru součásti je pro výrobu zvoleno vstřikování plastů, na které je dále zpracována literární rešerše. Následují technologické výpočty, na jejichž základě je navržena čtyřnásobná forma s horkým rozvodem taveniny a vyústěním přímo do tvarové dutiny formy. Forma je složena z nakupovaných komponent od dodavatele Meusburger, s výjimkou vyráběných tvarových vložek, které byly použity pro usnadnění vyrobitelnosti a snížení nákladů. Návrh je podložen simulační analýzou plnění, pomoci které byly určeny potenciálně nebezpečné zóny procesu, zejména oblasti uzavírání stlačeného vzduchu. Pro tato místa byla provedena opatření v podobě odvzdušňovacích kanálů. Na základě návrhu a doplňujících výpočtů je pro formu zvolen vstřikovací lis ARBURG ALLROUNDER 470 C GOLDEN EDITION. K práci je přiložena výkresová dokumentace.
The present thesis focuses on developing the manufacturing technology for a polycarbonate holder designed to attach motion and water level sensors to the walls of residential units. Based on an analysis of the requirements and the nature of the component, injection molding is identified as the most suitable production method. Research of this process is further elaborated. Technological calculations are then performed, leading to the design of a quadruple mold featuring a hot runner system and direct gating. Most mold components were sourced from the supplier Meusburger, with the exception of the mold inserts, which were custom-made to facilitate the manufacturability of the mold and reduce costs. A simulation analysis of the filling process was performed to identify potentially hazardous process zones, specifically areas where compressed air could be trapped. Venting solutions were implemented in these zones to mitigate any potential hazards. Following the design specifications and additional calculations, the ARBURG ALLROUNDER 470 C GOLDEN EDITION injection molding machine was selected for the mold. A drawing documentation is attached to the thesis.
The present thesis focuses on developing the manufacturing technology for a polycarbonate holder designed to attach motion and water level sensors to the walls of residential units. Based on an analysis of the requirements and the nature of the component, injection molding is identified as the most suitable production method. Research of this process is further elaborated. Technological calculations are then performed, leading to the design of a quadruple mold featuring a hot runner system and direct gating. Most mold components were sourced from the supplier Meusburger, with the exception of the mold inserts, which were custom-made to facilitate the manufacturability of the mold and reduce costs. A simulation analysis of the filling process was performed to identify potentially hazardous process zones, specifically areas where compressed air could be trapped. Venting solutions were implemented in these zones to mitigate any potential hazards. Following the design specifications and additional calculations, the ARBURG ALLROUNDER 470 C GOLDEN EDITION injection molding machine was selected for the mold. A drawing documentation is attached to the thesis.
Description
Citation
HORÁČEK, J. Návrh technologie výroby držáku senzoru [online]. Brno: Vysoké učení technické v Brně. Fakulta strojního inženýrství. 2024.
Document type
Document version
Date of access to the full text
Language of document
cs
Study field
Strojírenská technologie
Comittee
prof. Ing. Milan Forejt, CSc. (předseda)
prof. Ing. Radim Kocich, Ph.D. (místopředseda)
doc. Ing. Lenka Kunčická, Ph.D. (člen)
Ing. Miroslav Šlais, Ph.D. (člen)
Ing. Jiří Tomášek, CSc. (člen)
Ing. Vojtěch Staněk (člen)
Date of acceptance
2024-06-12
Defence
Student prezentoval komisi svou závěrečnou práci, její výstupy a závěry a zodpověděl dotazy oponenta. Dále byly studentovi položeny následující dotazy:
Ing. Tomášek – Jak byste postupoval při změně materiálu na plast plněný skleněnými vlákny? (otázka byla plně zodpovězena)
dr. Šlais – Jaké zkušenosti má firma se simulací v programu Solidworks Plastics 2023? (otázka byla plně zodpovězena)
dr. Šlais – Jaké znáte jiné programy pro simulování problematiky vstřikování plastů? (otázka byla plně zodpovězena)
Ing. Staněk – Z čeho se skládá vedlejší čas? (otázka byla plně zodpovězena)
Ing. Staněk – Je možné vedlejší čas snížit? (otázka byla plně zodpovězena)
Ing. Staněk – Na kolik odhadujete cenu nástroje? (otázka byla plně zodpovězena)
Result of defence
práce byla úspěšně obhájena
Document licence
Standardní licenční smlouva - přístup k plnému textu bez omezení