Precipitace intermetalických fází v duplexních austeniticko-feritických ocelích
Loading...
Date
Authors
Myška, Martin
ORCID
Advisor
Referee
Mark
P
Journal Title
Journal ISSN
Volume Title
Publisher
Vysoké učení technické v Brně. Fakulta strojního inženýrství
Abstract
Tato dizertační práce řeší problematiku precipitace intermetalických fází v lité duplexní korozivzdorné oceli dle normy ASTM A890 Gr4A. Cílem práce bylo stanovit množství vyloučených intermetalických fází v závislosti na teplotě a době výdrže při izotermickém žíhání a za anizotermických podmínek během chladnutí materiálu v intervalu teplot 1000 až 600 °C. Dílčím cílem práce bylo stanovit souvislosti mezi množstvím vyloučených intermetalických fází a mechanickými vlastnostmi lité oceli ASTM A890 Gr4A. V rámci práce byl ověřen popis a predikce kinetiky precipitace intermetalických fází pomocí Johnson-Mehl-Avramiho vztahu. Byla stanovena souvislost mezi množstvím vyloučených intermetalických fází a charakterem porušování materiálu pomocí fraktografického hodnocení. Byla stanovena kritická rychlost ochlazování odlitku pro zajištění minimální houževnatosti oceli, která je žádoucí pro snížení rizika vzniku trhlin při chladnutí odlitků z duplexních korozivzdorných ocelí.
This PhD thesis addresses the issue of precipitation of intermetallic phases in cast duplex stainless steel according to the ASTM A890 Gr4A standard. The aim of the thesis was to determine the amount of precipitated intermetallic phases depending on the temperature and holding time during isothermal annealing and under anisothermal conditions during cooling of the material in the temperature range from 1000 to 600 °C. The partial aim of the work was to determine the relationship between the amount of precipitated intermetallic phases and the mechanical properties of cast steel ASTM A890 Gr4A. As part of the work, the description and prediction of the kinetics of precipitation of intermetallic phases using the Johnson-Mehl-Avrami equation were verified. The relationship between the amount of precipitated intermetallic phases and the failure character of the material was determined by fractographic evaluation. The critical cooling rate of the casting was determined to ensure the minimum toughness of the steel that is desirable to reduce the risk of cracking during cooling of duplex stainless steel castings.
This PhD thesis addresses the issue of precipitation of intermetallic phases in cast duplex stainless steel according to the ASTM A890 Gr4A standard. The aim of the thesis was to determine the amount of precipitated intermetallic phases depending on the temperature and holding time during isothermal annealing and under anisothermal conditions during cooling of the material in the temperature range from 1000 to 600 °C. The partial aim of the work was to determine the relationship between the amount of precipitated intermetallic phases and the mechanical properties of cast steel ASTM A890 Gr4A. As part of the work, the description and prediction of the kinetics of precipitation of intermetallic phases using the Johnson-Mehl-Avrami equation were verified. The relationship between the amount of precipitated intermetallic phases and the failure character of the material was determined by fractographic evaluation. The critical cooling rate of the casting was determined to ensure the minimum toughness of the steel that is desirable to reduce the risk of cracking during cooling of duplex stainless steel castings.
Description
Citation
MYŠKA, M. Precipitace intermetalických fází v duplexních austeniticko-feritických ocelích [online]. Brno: Vysoké učení technické v Brně. Fakulta strojního inženýrství. 2023.
Document type
Document version
Date of access to the full text
Language of document
cs
Study field
Strojírenská technologie
Comittee
doc. Ing. Jaromír Roučka, CSc. (předseda)
prof. Ing. Rudolf Foret, CSc. (člen)
Ing. Jan Čech, Ph.D. (člen)
doc. Ing. Vít Jan, Ph.D. (člen)
RNDr. Jiří Svoboda, CSc. (člen)
doc. Ing. Jan Zouhar, Ph.D. (člen)
Date of acceptance
2023-08-15
Defence
DP řeší technicky významnou problematiku výroby a tepelného zpracování speciální vysokolegovaných ocelí na odlitky. Téma je technicky významné. Práce teoreticky analyzuje uvedenou problematiku a na konkrétních odlitých slitinách hodnotí jednotlivé procesní vlivy.Vlastní experimentální část má dostatečně velký rozsah a zahrnuje širokou škálu laboratorních a kontrolních metod . Časová náročnost řešení provedených zkoušek a jejich vyhodnocení je značná.Práce je přínosná pro teoretické poznání problematiky a praktické využití v reálné aplikaci. DP má dobrou formální úroveň a rozsah a oponenty byla kladně hodnocena. Výsledky práce, způsob prezentace před komisí a reakce doktoranda na dotazy byly hodnoceny kladně.
Result of defence
práce byla úspěšně obhájena
Document licence
Standardní licenční smlouva - přístup k plnému textu bez omezení