Elektronický momentový klíč
Loading...
Date
Authors
Juřík, Dominik
ORCID
Advisor
Referee
Mark
B
Journal Title
Journal ISSN
Volume Title
Publisher
Vysoké učení technické v Brně. Fakulta strojního inženýrství
Abstract
Tato bakalářská práce se zabývá zkonstruováním zařízení pro elektronický záznam utahovacího momentu a úhlu dotažení. Záznam procesu utahování se v praxi řeší pomocí elektronických momentových klíčů. Avšak tyto klíče jsou často velmi nákladné a jejich použití za účelem ověření spolehlivosti různých šroubových spojů by bylo značně nepraktické. Je to způsobeno velkými rozdíly potřebných utahovacích momentů pro různě velké šrouby. Tento problém byl v této práci vyřešen tím, že byl zkonstruován adaptér pro elektronický záznam utahování. Jelikož lze toto zařízení připojit pomocí připojovacího čtyřhranu k libovolně dlouhému klíči bez nutnosti další kalibrace. Měření a záznam utahovacího momentu je umožněn použitím tenzometrů, které jsou přilepené na prodlužovací tyči. K určování úhlu dotažení je použit senzor úhlové rychlosti (tzv. elektronický gyroskop). Signály ze senzorů jsou přenášeny do analyzátoru od firmy Dewetron pomocí konektoru na tomto adaptéru. Na základě provedeného experimentu lze říct, že je toto zařízení správně navrženo. Toto zařízení bude používáno v laboratoři Technické diagnostiky ÚK VUT.
This bachelor's thesis deals with the construction of a modification for a torque wrench for electronic recording of tightening torque and angle. In practice, the recording of the tightening process is managed using electronic torque wrenches. However, these wrenches are often very expensive, and their use for verifying the reliability of various screw joints would be highly impractical. This is due to the large differences in the required tightening torques for screws of different sizes. This problem has been addressed in this work by constructing an adapter for electronic recording of tightening. The measurement and recording of the tightening torque are enabled by using strain gauges, which are attached to an extension rod. An angular velocity sensor (an electronic gyroscope) is used to determine the tightening angle. Signals from the sensors are transmitted to an analyzer from Dewetron via a connector on this adapter. After initial calibration, this device can be connected via a square drive to any length of wrench without the need for further calibration. Based on the experiment conducted, it can be stated that this device is correctly designed. This device will be used in the Technical Diagnostics Laboratory of the Department of Mechanical Engineering at Brno University of Technology.
This bachelor's thesis deals with the construction of a modification for a torque wrench for electronic recording of tightening torque and angle. In practice, the recording of the tightening process is managed using electronic torque wrenches. However, these wrenches are often very expensive, and their use for verifying the reliability of various screw joints would be highly impractical. This is due to the large differences in the required tightening torques for screws of different sizes. This problem has been addressed in this work by constructing an adapter for electronic recording of tightening. The measurement and recording of the tightening torque are enabled by using strain gauges, which are attached to an extension rod. An angular velocity sensor (an electronic gyroscope) is used to determine the tightening angle. Signals from the sensors are transmitted to an analyzer from Dewetron via a connector on this adapter. After initial calibration, this device can be connected via a square drive to any length of wrench without the need for further calibration. Based on the experiment conducted, it can be stated that this device is correctly designed. This device will be used in the Technical Diagnostics Laboratory of the Department of Mechanical Engineering at Brno University of Technology.
Description
Citation
JUŘÍK, D. Elektronický momentový klíč [online]. Brno: Vysoké učení technické v Brně. Fakulta strojního inženýrství. 2024.
Document type
Document version
Date of access to the full text
Language of document
cs
Study field
Základy strojního inženýrství
Comittee
doc. Ing. Daniel Koutný, Ph.D. (předseda)
doc. Ing. Petr Svoboda, Ph.D. (místopředseda)
Ing. Radovan Galas, Ph.D. (člen)
Ing. Ondřej Červinek, Ph.D. (člen)
Ing. Zbyněk Strecker, Ph.D. (člen)
Date of acceptance
2024-06-10
Defence
Student prezentoval výsledky své bakalářské práce a zodpověděl otázky oponenta.
Otázka oponenta 1: V kapitole 5.5 uvádíte konstrukci přípravku na kalibraci. V textu jsem se nedočetl, proč je přípravek nutný a proč byla zvolena právě tato konstrukce. Prosím o vysvětlení. – ZODPOVĚZENO
doc. Koutný: Jakým způsobem plánujete zpracovávat signály? - ZODPOVĚZENO
doc. Koutný: Jakým způsobem uživatel zkombinuje informace z tenzometru a z gyroskopu? – ZODPOVĚZENO
doc. Svoboda: Jaký je rozsah a přesnost zařízení? - ZODPOVĚZENO
doc. Svoboda: Na jaké průměry šroubu je zařízení vhodné? – ZODPOVĚZENO
dr. Červinek: Jaká je opakovatelnost měření? – ZODPOVĚZENO
Result of defence
práce byla úspěšně obhájena
Document licence
Standardní licenční smlouva - přístup k plnému textu bez omezení