Analogový vstupní díl pro softwarový přijímač
Loading...
Date
Authors
Slezák, Jakub
ORCID
Advisor
Referee
Mark
A
Journal Title
Journal ISSN
Volume Title
Publisher
Vysoké učení technické v Brně. Fakulta elektrotechniky a komunikačních technologií
Abstract
Tato diplomová práce se zabývá teoretickým rozborem základních parametrů přijímačů, architekturou vstupních obvodů a digitalizací signálů. Podle zadání je navrženo blokové schéma analogového vstupního dílu softwarového přijímače s již konkrétními součástkami a je spočítána celková bilance tohoto zapojení. Následně jsou navrženy a prakticky realizovány jednotlivé části celého systému. Jedná se o sadu čtyř vstupních filtrů pro pásma: krátké vlny do 30 MHz, 87,5-108 MHz, 144-148 MHz a 174-230 MHz. Hlavním bodem návrhu je obvod obsahující nízkošumové zesilovače, přepínače a dva zesilovače s řiditelným zesílením. Převážně jsou použity integrované obvody od firmy Analog Devices. Pro ovládání jednotlivých přepínačů a řiditelných zesilovačů byl navržen samostatný přípravek, který je s hlavním obvodem propojen kabelem. V poslední fázi byl celý systém i jeho jednotlivé části podrobeny měření. Zejména díky množství osazených SMA konektorů je možno změřit jednotlivé části systému a také máme možnost ho částečně modifikovat.
This thesis deals with a theoretical analysis of the basic parameters of receivers, input circuit architecture and signal digitization. According to the specified assignment it is outlined block scheme of front end for software receiver with specified components and the total bilance is calculated. Individual parts of the system are designed and realized. This is a set of four input filters for bandwidths: short waves up to 30 MHz, 87,5-108 MHz, 144-148 MHz and 174-230 MHz. The main point of design is a circuit containing a low-noise amplifiers, switches, and two amplifiers with adjustable amplification. Mainly are used integrated circuits from Analog Devices corporation. To control the various switches and adjustable amplifiers was designed a separate panel, which is connected to the main circuit via a cable. In the last phase was the whole system and its components subjected to measurements. Thanks to a number of mounted SMA connectors it is possible to measure different parts of the system and we are able to modify it partially.
This thesis deals with a theoretical analysis of the basic parameters of receivers, input circuit architecture and signal digitization. According to the specified assignment it is outlined block scheme of front end for software receiver with specified components and the total bilance is calculated. Individual parts of the system are designed and realized. This is a set of four input filters for bandwidths: short waves up to 30 MHz, 87,5-108 MHz, 144-148 MHz and 174-230 MHz. The main point of design is a circuit containing a low-noise amplifiers, switches, and two amplifiers with adjustable amplification. Mainly are used integrated circuits from Analog Devices corporation. To control the various switches and adjustable amplifiers was designed a separate panel, which is connected to the main circuit via a cable. In the last phase was the whole system and its components subjected to measurements. Thanks to a number of mounted SMA connectors it is possible to measure different parts of the system and we are able to modify it partially.
Description
Keywords
šumové číslo, intermodulace, dynamický rozsah, zesilovač, softwarově definované rádio, A/D převodník, podvzorkování, pásmová propust, nízkošumový zesilovač, přepínač, automatické řízení zisku, noise figure, intermodulation, dynamic range, amplifier, software defined radio, A/D convertor, undersampling, band pass filter, low noise amplifier, switch, automatic gain control
Citation
SLEZÁK, J. Analogový vstupní díl pro softwarový přijímač [online]. Brno: Vysoké učení technické v Brně. Fakulta elektrotechniky a komunikačních technologií. 2012.
Document type
Document version
Date of access to the full text
Language of document
cs
Study field
Elektronika a sdělovací technika
Comittee
prof. Ing. Stanislav Hanus, CSc. (předseda)
Ing. Jiří Dřínovský, Ph.D. (místopředseda)
Ing. Dr. Techn. Vojtěch Derbek (člen)
doc. Ing. Roman Šotner, Ph.D. (člen)
doc. Ing. Jiří Masopust, CSc. (člen)
Ing. Jana Olivová, Ph.D. (člen)
Date of acceptance
2012-06-05
Defence
Student prezentuje výsledky a postupy řešení své
diplomové práce. Následně odpovídá na dotazy vedoucího
a oponenta práce a na dotazy členů zkušební komise.
Result of defence
práce byla úspěšně obhájena
Document licence
Standardní licenční smlouva - přístup k plnému textu bez omezení