Hodnocení obrobitelnosti materiálu vyrobeného pomocí aditivní technologie
Loading...
Date
Authors
Bílek, Richard
ORCID
Advisor
Referee
Mark
A
Journal Title
Journal ISSN
Volume Title
Publisher
Vysoké učení technické v Brně. Fakulta strojního inženýrství
Abstract
Tato bakalářská práce se zabývá hodnocením obrobitelnosti vysoce pevnostní maraging oceli M300, která je vyrobena ve třech typech vzorků. Dva vzorky byly aditivně vyrobeny metodou Selective Laser Melting, z nichž byl jeden následně tepelně zpracován. Třetí vzorek byl vyroben konvenčním způsobem pomocí válcování. Testování probíhalo frézováním za různých řezných podmínek. V praktické části byly odebrány vzniklé třísky a měřeny tvrdosti jednotlivých vzorků, dále pak jednotlivé složky silového zatížení během obrábění, drsnosti povrchu a opotřebení na hřbetu nástroje. Naměřená data a morfologie třísek byly dále analyzovány a vyhodnocovány. Výstupem práce je doporučení vhodné řezné rychlosti pro obrábění aditivně vyrobené oceli maraging M300.
This bachelor thesis evaluates the machinability of high strength maraging steel M300, which is produced in three types of samples. Two samples were additively manufactured by Selective Laser Melting, one of which was subsequently heat treated. The third sample was produced by conventional rolling. Testing was carried out by milling under different cutting conditions. In the practical part the resulting chips were taken and hardness of individual samples, then the individual cutting forces during machining, surface roughness and the flank wear were measured. The measured data and chips morphology were further analysed and evaluated. The output of the work is a recommendation of the appropriate cutting speed for machining the additively manufacturing maraging steel M300.
This bachelor thesis evaluates the machinability of high strength maraging steel M300, which is produced in three types of samples. Two samples were additively manufactured by Selective Laser Melting, one of which was subsequently heat treated. The third sample was produced by conventional rolling. Testing was carried out by milling under different cutting conditions. In the practical part the resulting chips were taken and hardness of individual samples, then the individual cutting forces during machining, surface roughness and the flank wear were measured. The measured data and chips morphology were further analysed and evaluated. The output of the work is a recommendation of the appropriate cutting speed for machining the additively manufacturing maraging steel M300.
Description
Citation
BÍLEK, R. Hodnocení obrobitelnosti materiálu vyrobeného pomocí aditivní technologie [online]. Brno: Vysoké učení technické v Brně. Fakulta strojního inženýrství. 2024.
Document type
Document version
Date of access to the full text
Language of document
cs
Study field
Strojírenská technologie
Comittee
doc. Ing. Josef Sedlák, Ph.D. (předseda)
prof. Ing. Robert Čep, Ph.D. (místopředseda)
doc. Ing. Ivan Buranský, PhD. (člen)
prof. Dr. Ing. Libor Beneš (člen)
Ing. Miroslav Frost (člen)
doc. Ing. Martin Novák, Ph.D. (člen)
Date of acceptance
2024-06-11
Defence
Bakalář seznámil komisi s obsahem a výsledky své bakalářské práce a zodpověděl otázky vedoucího, oponenta a dalších členů komise:
V průběhu obhajoby byly zodpovězeny následující doplňující otázky:
1. Jakým způsobem je hodnocen parametr Rz?
zodpovězeno
2. Jaké jsou hlavní závěry z dané práce?
zodpovězeno
Otázky členů komise byly zodpovězeny.
Result of defence
práce byla úspěšně obhájena
Document licence
Standardní licenční smlouva - přístup k plnému textu bez omezení