Zvýšení jakosti disků automobilových kol odlévaných metodou nízkotlakého lití
Loading...
Date
Authors
Bělota, Martin
ORCID
Advisor
Referee
Mark
B
Journal Title
Journal ISSN
Volume Title
Publisher
Vysoké učení technické v Brně. Fakulta strojního inženýrství
Abstract
Diplomová práce se zabývá identifikací vad vyskytujících se u litých automobilových kol. Součástí diplomové práce je také návrh a experimentální ověření opatření, která vedou ke zvýšení jakosti produkce. První kapitola teoretické části se zabývá výskytem plynů ve slitinách hliníku, především vodíku, jeho zdroji, rozpustností ve slitinách hliníku a vznikem plynových dutin v odlitcích. V druhé kapitole jsou popsány způsoby odplynění taveniny vakuováním a probubláváním inertními a aktivními plyny. Třetí kapitola pojednává o řízeném naplynění taveniny, účelem naplyňování taveniny a metodami řízeného naplynění. Čtvrtá kapitola je věnována vadám, které se vyskytují u automobilových kol vyrobených technologií nízkotlakého lití. V páté kapitole je popsána slitina hliníku AlSi7Mg0,3, která se používá k výrobě litých kol. Je zde popsáno i tepelné zpracování litých kol. Šestá kapitola se zabývá praktickou částí diplomové práce, ve které je provedena identifikace vad mikroskopickými a radiografickými metodami. V další části je popsán návrh a provedení experimentu, ve kterém byl na základě výsledků identifikace vad vybrán přípravek Probat-Fluss MIKRO 100 ke zvýšení jakosti produkce. V závěru praktické části je vyhodnocen provedený experiment, který také sloužil k ověření účinnosti přípravku Probat-Fluss MIKRO 100.
The thesis deals with the identification of defects occurring in cast automotive wheels. The thesis also includes the design and experimental verification of measures that lead to an increase in the quality of production. The first chapter of the theoretical part deals with the occurrence of gases in aluminium alloys, especially hydrogen, its sources, solubility in aluminium alloys and the formation of gas cavities in castings. The second chapter describes ways of degassing the melt by vacuuming and bubbling with inert and active gases. The third chapter deals with controlled melt gasification, the purpose of melt gassing and methods of controlled gassing. The fourth chapter is devoted to the defects that occur in automotive wheels produced by lowpressure die casting technology. The fifth chapter describes the aluminum alloy AlSi7Mg0.3, which is used for the manufacture of cast wheels. It also describes the heat treatment of cast wheels. The sixth chapter deals with the practical part of the thesis, which includes the identification of defects using microscopic and radiographic methods. The next part describes the design and execution of an experiment in which Probat-Fluss MIKRO 100 was selected to improve the quality of production based on the results of defect identification. At the end of the practical part, the conducted experiment is evaluated, which also served to verify the effectiveness of Probat-Fluss MIKRO 100.
The thesis deals with the identification of defects occurring in cast automotive wheels. The thesis also includes the design and experimental verification of measures that lead to an increase in the quality of production. The first chapter of the theoretical part deals with the occurrence of gases in aluminium alloys, especially hydrogen, its sources, solubility in aluminium alloys and the formation of gas cavities in castings. The second chapter describes ways of degassing the melt by vacuuming and bubbling with inert and active gases. The third chapter deals with controlled melt gasification, the purpose of melt gassing and methods of controlled gassing. The fourth chapter is devoted to the defects that occur in automotive wheels produced by lowpressure die casting technology. The fifth chapter describes the aluminum alloy AlSi7Mg0.3, which is used for the manufacture of cast wheels. It also describes the heat treatment of cast wheels. The sixth chapter deals with the practical part of the thesis, which includes the identification of defects using microscopic and radiographic methods. The next part describes the design and execution of an experiment in which Probat-Fluss MIKRO 100 was selected to improve the quality of production based on the results of defect identification. At the end of the practical part, the conducted experiment is evaluated, which also served to verify the effectiveness of Probat-Fluss MIKRO 100.
Description
Citation
BĚLOTA, M. Zvýšení jakosti disků automobilových kol odlévaných metodou nízkotlakého lití [online]. Brno: Vysoké učení technické v Brně. Fakulta strojního inženýrství. 2024.
Document type
Document version
Date of access to the full text
Language of document
cs
Study field
bez specializace
Comittee
prof. Ing. Milan Horáček, CSc. (předseda)
doc. Ing. Antonín Záděra, Ph.D. (místopředseda)
doc. Ing. Libor Čamek, Ph.D. (člen)
doc. Ing. Libor Pantělejev, Ph.D. (člen)
Ing. Jan Čech, Ph.D. (člen)
Ing. Ladislav Tomek (člen)
Date of acceptance
2024-06-12
Defence
Student Martin Bělota svou prezentací seznámil zkušební komisi s obsahem práce. Práce byla přednesena ve stanoveném čase.
Po prezentaci a přečtení posudků práce byl student vyzván k zodpovězení otázek oponenta, které podrobně zodpověděl. K práci byly vzneseny připomínky a následující otázky:
Na jakém principu funguje váš používaný přípravek Mikro 100, kdy probíhá jeho aplikace? zodpovězeno;
Jaké byly provedeny statistické analýzy? zodpovězeno;
Jak byste plánoval další experimenty? částečně zodpovězeno;
Nalezl jste v rámci své rešerše na odplyňování taveniny pomocí vakua? zodpovězeno;
Result of defence
práce byla úspěšně obhájena
Document licence
Standardní licenční smlouva - přístup k plnému textu bez omezení