Mechanické vlastnosti Al slitiny připravené pomocí procesu SLM
but.committee | prof. Ing. Ivo Dlouhý, CSc. (předseda) prof. Ing. Jiří Švejcar, CSc. (místopředseda) prof. Ing. Rudolf Foret, CSc. (člen) prof. RNDr. Karel Maca, Dr. (člen) prof. Mgr. Tomáš Kruml, CSc. (člen) doc. Ing. Jana Sobotová, Ph.D. (člen) | cs |
but.defence | cs | |
but.jazyk | čeština (Czech) | |
but.program | Aplikované vědy v inženýrství | cs |
but.result | práce byla úspěšně obhájena | cs |
dc.contributor.advisor | Pantělejev, Libor | cs |
dc.contributor.author | Vitásek, Ladislav | cs |
dc.contributor.referee | Štěpánek, Roman | cs |
dc.date.accessioned | 2019-04-03T22:08:00Z | |
dc.date.available | 2019-04-03T22:08:00Z | |
dc.date.created | 2017 | cs |
dc.description.abstract | Tato diplomová práce se zabývá vlastnostmi hliníkových slitin vyráběných procesem SLM. Rešeršní část práce je zaměřena na popis technologie selektivního laserového tavení, defekty mikrostruktury a mechanické vlastnosti hliníkových slitin připravených touto technologií. Experimentální část práce se zabývá volbou parametrů procesu SLM za účelem přípravy objemných vzorků. Základní mechanické charakteristiky byly určovány zkouškou tahem za pokojové teploty. V rámci práce byla také hodnocena mikrostruktura materiálů a prováděna fraktografická analýza pro posouzení mechanismů porušování. Získané materiálové charakteristiky byly porovnány s vlastnostmi materiálů stejných skupin vyráběných konvenčními technologiemi. | cs |
dc.description.abstract | The master's thesis deals with properties of aluminium alloys prepared by SLM process. The teoretical part of thesis is focused on decribtion of selective laser melting technology, metallurgical defects and mechanical properties of aluminium alloys processed by this technology. The experimental part of this thesis deals with selections of the SLM process parameters suitable for samples preparation in bulk. Tensile testing at room temperature was used for evaluation of basic mechanical properties. Metallographic and fractographic analyses were performed for evaluation of the microstructure and fracture mechanisms. The materials characteristics obtained on SLM samples were compared with the properties of the same materials grade produced by conventional technologies. | en |
dc.description.mark | A | cs |
dc.identifier.citation | VITÁSEK, L. Mechanické vlastnosti Al slitiny připravené pomocí procesu SLM [online]. Brno: Vysoké učení technické v Brně. Fakulta strojního inženýrství. 2017. | cs |
dc.identifier.other | 101330 | cs |
dc.identifier.uri | http://hdl.handle.net/11012/67482 | |
dc.language.iso | cs | cs |
dc.publisher | Vysoké učení technické v Brně. Fakulta strojního inženýrství | cs |
dc.rights | Standardní licenční smlouva - přístup k plnému textu bez omezení | cs |
dc.subject | Selektivní laserové tavení (SLM) | cs |
dc.subject | AlCu2Mg1 | cs |
dc.subject | 5Ni | cs |
dc.subject | AlSi9Cu3 a AlSi10Mg | cs |
dc.subject | mechanické vlastnosti | cs |
dc.subject | Selective laser melting (SLM) | en |
dc.subject | AlCu2Mg1.5Ni | en |
dc.subject | AlSi9Cu3 and AlSi10Mg | en |
dc.subject | mechanical properties | en |
dc.title | Mechanické vlastnosti Al slitiny připravené pomocí procesu SLM | cs |
dc.title.alternative | Mechanical properties of Al alloy prepared by SLM process | en |
dc.type | Text | cs |
dc.type.driver | masterThesis | en |
dc.type.evskp | diplomová práce | cs |
dcterms.dateAccepted | 2017-06-13 | cs |
dcterms.modified | 2017-06-14-11:10:40 | cs |
eprints.affiliatedInstitution.faculty | Fakulta strojního inženýrství | cs |
sync.item.dbid | 101330 | en |
sync.item.dbtype | ZP | en |
sync.item.insts | 2021.11.12 18:19:02 | en |
sync.item.modts | 2021.11.12 17:34:39 | en |
thesis.discipline | Materiálové inženýrství | cs |
thesis.grantor | Vysoké učení technické v Brně. Fakulta strojního inženýrství. Ústav materiálových věd a inženýrství | cs |
thesis.level | Inženýrský | cs |
thesis.name | Ing. | cs |