Analýza rozdílů v působení předpjatých horninových kotev v různých inženýrskogeologických podmínkách
Loading...
Date
Authors
Chylík, Zdeněk
ORCID
Advisor
Referee
Mark
A
Journal Title
Journal ISSN
Volume Title
Publisher
Vysoké učení technické v Brně. Fakulta stavební
Abstract
Tato diplomová práce se zabývá popisem chování horninových kotev při tahovém zatěžování. Tento popis je umožněn díky měření deformací pomocí optických snímačů podél celé délky kotvy. Práce je rozdělena do osmi kapitol. V první, druhé a třetí kapitole je uveden úvod k obsahu práce se stručnou motivací, charakteristika návrhu kotev s popisem jejich konstrukce a základní informace o optických snímačích. Ve čtvrté kapitole je objasněn princip vyhodnocení jednotlivých parametrů a v páté kapitole je uveden přehled všech zkoumaných kotev. Šestá kapitola je věnována vyhodnocení jednotlivých kotev vždy s popisem dané oblasti. Sedmá kapitola obsahuje srovnání vyhodnocených parametrů. Mezi zjištěné parametry patří: plášťové tření, rozvoj separace táhla v injektáži, rozdílnost posunů a sil stanové dvěma metodami monitoringu, parametr Ms a koeficient . Osmá, závěrečná kapitola obsahuje závěr.
This thesis focuses on describing the behavior of ground anchors during pull-out tests. Optical sensors enabled this description because they measure the deformation along the entire anchor. The thesis is divided into eight chapters. Chapters one, two and three contain an introduction to the content of the thesis, characteristics of the design of anchors with a description of their construction and basic information about optical sensors. Chapter four explains the principle of evaluation of each parameter and chapter five gives an overview of all the anchors investigated. The sixth chapter contains an evaluation of each anchor with a description of each area. The seventh chapter contains a comparison of the evaluated parameters. Among the parameters found are: skin friction, the evolution of debonding, differences of tendon displacement and forces in tendon determined by two monitoring methods, parameter Ms and coefficient . The thesis ends with chapter eight, which contains final conclusion.
This thesis focuses on describing the behavior of ground anchors during pull-out tests. Optical sensors enabled this description because they measure the deformation along the entire anchor. The thesis is divided into eight chapters. Chapters one, two and three contain an introduction to the content of the thesis, characteristics of the design of anchors with a description of their construction and basic information about optical sensors. Chapter four explains the principle of evaluation of each parameter and chapter five gives an overview of all the anchors investigated. The sixth chapter contains an evaluation of each anchor with a description of each area. The seventh chapter contains a comparison of the evaluated parameters. Among the parameters found are: skin friction, the evolution of debonding, differences of tendon displacement and forces in tendon determined by two monitoring methods, parameter Ms and coefficient . The thesis ends with chapter eight, which contains final conclusion.
Description
Keywords
Geotechnika, horninová kotva, volná délka táhla, kořenová délka táhla, přetvoření, posun táhla, posun injektáže, injektáž, zatěžovací zkouška, optický snímač, metoda přenosových funkcí, metoda, plášťové tření, separace táhla v injektáži, Geotechnics, ground anchor, free length, bond length, strain, tendon displacement, grout displacement, grout, pullout test, optic sensor, load transfer method, method, skin friction, debonding
Citation
CHYLÍK, Z. Analýza rozdílů v působení předpjatých horninových kotev v různých inženýrskogeologických podmínkách [online]. Brno: Vysoké učení technické v Brně. Fakulta stavební. 2025.
Document type
Document version
Date of access to the full text
Language of document
cs
Study field
bez specializace
Comittee
doc. Ing. Alexandr Rozsypal, CSc. (předseda)
doc. Ing. Vladislav Horák, CSc. (místopředseda)
Ing. Petr Svoboda, Ph.D. (člen)
Ing. Lumír Kliš (člen)
Ing. Věra Glisníková, CSc. (člen)
doc. Ing. Lumír Miča, Ph.D. (člen)
Ing. Juraj Chalmovský, Ph.D. (člen)
prof. RNDr. Lukáš Krmíček, Ph.D. (člen)
Date of acceptance
2025-02-05
Defence
Student Bc. Zdeněk Chylík obhajoval závěrečnou práci s názvem "Analýza rozdílů v působení předpjatých horninových kotev v různých inženýrskogeologických podmínkách".
Po prezentaci práce bylo přečteno hodnocení vedoucího a posudek oponenta práce, na jejichž otázky a připomínky student reagoval.
Poté proběhla obhajoba práce.
Student odpovídal na tyto dotazy předsedy a členů zkušební komise:
Fungovalo v napínacím programu i tření na plášti a je splněno kritérium příslušné normy?
Co je příčinou záporných hodnot posunů?
Jak probíhalo dodatečné injektování?
Byly zkoušky provedeny v rámci monitoringu nebo firemního programu a mohly by se tedy pak stát součástí monitoringu?
Jaké bylo uchycení snímačů?
Na položené otázky odpovídal student výborně .
Result of defence
práce byla úspěšně obhájena
Document licence
Standardní licenční smlouva - přístup k plnému textu bez omezení