Návrh racionalizace výroby tvarové části vstřikovací formy
Loading...
Date
Authors
Kamenická, Eva
ORCID
Advisor
Referee
Mark
A
Journal Title
Journal ISSN
Volume Title
Publisher
Vysoké učení technické v Brně. Fakulta strojního inženýrství
Abstract
Diplomová práca sa zaoberá návrhom zefektívnenia výroby tvarovej časti vstrekovacej formy a dielu formy zodpovedného za chladenie plastového výrobku. Hlavným cieľom je skrátenie výrobného času so súčasným dodržaním vysokých požiadaviek na rozmerovú a geometrickú presnosť a integritu povrchu vyrábaných súčastí. Práca sa na začiatku venuje teoretickému rozboru problematiky výroby tvarových častí foriem. Nasleduje analýza východzieho stavu, ktorá pozostáva z charakteristiky daných súčastí, dostupných výrobných prostriedkov a z popisu pôvodného technologického postupu. Experimentálna časť práce vysvetľuje postupy a zdôvodňuje voľby pri tvorbe nových programov v prostredí CAM softvéru Cimatron. Niekoľko možných variánt nástrojov a rezných parametrov bolo experimentálne odskúšaných a ich konečná voľba je v práci odôvodnená. Výstupom práce je nový technologický postup pre výrobu oboch súčastí, ktorý bol v praxi realizovaný a ohodnotený na základe výsledkov testov kvality súčastí i plastového výrobku. V závere práce možno nájsť zhodnotenie výstupu práce a časové porovnanie predošlého postupu s novým návrhom. Všetky experimenty a merania, vrátane výroby samotných súčastí, boli realizované v nástrojárni závodu spoločnosti ITW PRONOVIA, s.r.o. vo Veľkej Bíteši, ktorá je zároveň zadávateľom tejto práce.
The diploma thesis deals with suggestion for rationalization of production of an injection mould cavity plate and of a part responsible for cooling of the final plastic product. The main objective is to reduce the production time while meeting the high requirements for dimensional and geometric accuracy and surface integrity of the manufactured parts. The thesis starts with a theoretical analysis of the production of mould parts. This is followed by an analysis of the initial state of production, which consists of the characteristics of the previously mentionned manufactured parts, the available production means and a description of the original technological process. The experimental part of the thesis explains the procedures and justifies the choices made in the creation of new programmes within the CAM software Cimatron. Several possible variations of tools and cutting parameters have been experimentally tested and their final choice is justified in the thesis. The output of the thesis is a new manufacturing process for the production of both components, which has been applied in practice and evaluated on the basis of the results of testing the quality of the components and the plastic product itself. In the conclusion of the thesis can be found an evaluation of the output of the thesis and a time comparison of the previous process with the new suggestion. All experiments and measurements, including the production of the components themselves, were carried out in the toolroom of ITW PRONOVIA, s.r.o. in Veľká Bíteš, which is also the creator of the topic of this thesis.
The diploma thesis deals with suggestion for rationalization of production of an injection mould cavity plate and of a part responsible for cooling of the final plastic product. The main objective is to reduce the production time while meeting the high requirements for dimensional and geometric accuracy and surface integrity of the manufactured parts. The thesis starts with a theoretical analysis of the production of mould parts. This is followed by an analysis of the initial state of production, which consists of the characteristics of the previously mentionned manufactured parts, the available production means and a description of the original technological process. The experimental part of the thesis explains the procedures and justifies the choices made in the creation of new programmes within the CAM software Cimatron. Several possible variations of tools and cutting parameters have been experimentally tested and their final choice is justified in the thesis. The output of the thesis is a new manufacturing process for the production of both components, which has been applied in practice and evaluated on the basis of the results of testing the quality of the components and the plastic product itself. In the conclusion of the thesis can be found an evaluation of the output of the thesis and a time comparison of the previous process with the new suggestion. All experiments and measurements, including the production of the components themselves, were carried out in the toolroom of ITW PRONOVIA, s.r.o. in Veľká Bíteš, which is also the creator of the topic of this thesis.
Description
Citation
KAMENICKÁ, E. Návrh racionalizace výroby tvarové části vstřikovací formy [online]. Brno: Vysoké učení technické v Brně. Fakulta strojního inženýrství. 2023.
Document type
Document version
Date of access to the full text
Language of document
sk
Study field
Strojírenská technologie
Comittee
doc. Ing. Josef Sedlák, Ph.D. (předseda)
doc. Ing. Jozef Majerík, Ph.D. (místopředseda)
doc. Ing. Igor Barényi, Ph.D. (člen)
doc. Ing. Mário Drbúl, PhD. (člen)
doc. Ing. Jan Zouhar, Ph.D. (člen)
Ing. Miroslav Frost (člen)
Date of acceptance
2023-06-14
Defence
Diplomantka seznámila komisi s obsahem a výsledky své diplomové práce a zodpověděla otázky vedoucího, oponenta a dalších členů komise:
V průběhu obhajoby byly zodpovězeny následující doplňující otázky:
1. Z jakého důvodu docházelo k vibracím v rohových oblastech formy?
zodpovězeno
2. V jakém programu byly programovány dráhy při obrábění?
zodpovězeno
3. Jakým způsobem byl realizován odvod třísek z místa řezu?
zodpovězeno
4. Docházelo k vyvažování nástrojů před obráběním?
Zodpovězeno
Otázky členů komise byly zodpovězeny
Result of defence
práce byla úspěšně obhájena
Document licence
Standardní licenční smlouva - přístup k plnému textu bez omezení