Optimalizace vlastností nástřiku připraveného metodou Cold Spray pomocí tepelného zpracování
Loading...
Date
Authors
Bartošík, Vojtěch
ORCID
Advisor
Referee
Mark
A
Journal Title
Journal ISSN
Volume Title
Publisher
Vysoké učení technické v Brně. Fakulta strojního inženýrství
Abstract
Tato bakalářská práce se zabývá volbou parametrů tepelného zpracování kovového povlaku austenitické nestabilizované korozivzdorné oceli AISI 304L naneseného metodou Cold spray. Pomocí vhodného tepelného zpracování je možné upravovat mechanické vlastnosti, snížit pórovitost a v neposlední řadě také odstranit vysoká reziduální napětí v materiálu. Teoretická část práce je věnována literární rešerši na téma technologie Cold spray, koroze a korozivzdorných ocelí. V experimentální části jsou popsány postupy při měření vzorků, které prošly tepelným zpracováním, které probíhalo v rozmezí teplot 500 až 1100 °C, vždy při hodinové výdrži na teplotě a ochlazením na vzduchu. Kromě těchto vzorků byl materiál zkoumán i ve výchozím stavu. Byla stanovena pórovitost, mikrotvrdost a také magnetičnost. K analýze struktury byly pořízeny fotografie na světelném i elektronovém skenovacím mikroskopu. Na základě výsledků se jako dobrá volba zdá tepelné zpracování s hodinovou výdrží na teplotě 700 °C, kde byl pozorován významný pokles pórovitosti, částečné zotavení struktury při zachování vysoké mikrotvrdosti a také jemnosti zrna.
This bachelor's thesis deals with the choice of heat treatment parameters of the metal coating of austenitic unstabilized stainless steel AISI 304L applied by the Cold spray method. With the help of suitable heat treatment, it is possible to adjust the mechanical properties, reduce the porosity and, last but not least, also remove high residual stresses in the material. The theoretical part of the work is devoted to literature research on the topic of Cold spray technology, corrosion and corrosion-resistant steels. The experimental part describes the procedures for measuring samples that have undergone heat treatment. This took place in the temperature range of 500 to 1100 °C, always with an hour's holding time at the temperature, followed by cooling in air. In addition to these samples, the material was also examined in its initial state. Porosity, microhardness and also magnetism were determined. To analyze the structure, photographs were taken on a light and electron scanning microscope. Based on the results, heat treatment with an hourly hold at 700 °C seems to be a good choice, where a significant decrease in porosity, partial recovery of the structure while maintaining high microhardness and also grain fineness was observed.
This bachelor's thesis deals with the choice of heat treatment parameters of the metal coating of austenitic unstabilized stainless steel AISI 304L applied by the Cold spray method. With the help of suitable heat treatment, it is possible to adjust the mechanical properties, reduce the porosity and, last but not least, also remove high residual stresses in the material. The theoretical part of the work is devoted to literature research on the topic of Cold spray technology, corrosion and corrosion-resistant steels. The experimental part describes the procedures for measuring samples that have undergone heat treatment. This took place in the temperature range of 500 to 1100 °C, always with an hour's holding time at the temperature, followed by cooling in air. In addition to these samples, the material was also examined in its initial state. Porosity, microhardness and also magnetism were determined. To analyze the structure, photographs were taken on a light and electron scanning microscope. Based on the results, heat treatment with an hourly hold at 700 °C seems to be a good choice, where a significant decrease in porosity, partial recovery of the structure while maintaining high microhardness and also grain fineness was observed.
Description
Citation
BARTOŠÍK, V. Optimalizace vlastností nástřiku připraveného metodou Cold Spray pomocí tepelného zpracování [online]. Brno: Vysoké učení technické v Brně. Fakulta strojního inženýrství. 2023.
Document type
Document version
Date of access to the full text
Language of document
cs
Study field
Základy strojního inženýrství
Comittee
doc. Ing. Vít Jan, Ph.D. (předseda)
doc. Ing. Bohumil Pacal, CSc. (místopředseda)
Ing. Libor Válka, CSc. (člen)
Ing. Lenka Klakurková, Ph.D. (člen)
prof. Ing. Martin Trunec, Dr. (člen)
Date of acceptance
2023-06-14
Defence
Student prezentoval svou záverečnou práci a odpověděl na otázky oponenta. Dále odpověděl na otázky komise, konkrétně:
Co se děje s atmosférou v póru při tepelném zpracování? - odpovězeno
Jak vznikají dvojčata ve vzorku po tepelném zpracování? - odpovězeno
Čím se liší delta ferit od austenitu? - odpovězeno
Jaké póry lze měřit Archimedovou metodou? - odpovězeno
Jaké nedestruktivní metody lze aplikovat pro měření porozity? - neodpovězeno
Proč při 500 °C vzrostla porozita? - odpovězena částečně
Lze porovnávat tvrdosti při různých zatíženích a při jakém zatížení bude hodnota vyšší? - odpovězeno
Co považujete za heterogenitu? - odpovězeno
Result of defence
práce byla úspěšně obhájena
Document licence
Standardní licenční smlouva - přístup k plnému textu bez omezení