Jednofázový střídač s výstupními parametry 230 V / 50 Hz / 100 VA
Loading...
Date
Authors
Smolák, Martin
ORCID
Advisor
Referee
Mark
A
Journal Title
Journal ISSN
Volume Title
Publisher
Vysoké učení technické v Brně. Fakulta elektrotechniky a komunikačních technologií
Abstract
Cílem této diplomové práce byla optimalizace silových a řídicích obvodů střídače, který byl vyvinutý na UVEE. V této práci je popsán princip funkce a obvodové realizace jednofázového střídače. V práci jsou odvozeny různé výpočty (návrh LC filtru, kondenzátoru v meziobvodu, dimenzování polovodičových prvků a návrh chladiče pro odvod ztrátového výkonu). V řídicí části jsou odvozené rovnice pro výpočty kmitočtu oscilačních kmitů RC oscilátoru, návrh generátoru pilového signálu a návrh rychlé nadproudové ochrany. Dále byla navržena deska plošných spojů, která se optimalizovala pomocí tepelné simulace v programu Workbench Ansys. Následně je deska plošných spojů osazená, oživená a byla na ní provedena série ověřovacích měření. V závěru práce je vypracována dokumentace k realizovanému zařízení.
This master‘s thesis focuses on optimization of power and control circuits of an inverter, which was developed at UVEE. The principle of function and circuit implementation of a single-phase inventer, various calculations (design of an LC filter, DC link capacitor, semiconductor elements and heat sink) are described in the thesis. A design of fast overcurrent protections, oscillator and saw signal generator is included. Furthermore, a printed circuit board was designed which was optimized by thermal simulation in the Workbench Ansys. Subsequently, the printed circuit board was mounted, debugged and verification measurements were performed on it. At the end of the thesis there is a documentation for the implemented equipment.
This master‘s thesis focuses on optimization of power and control circuits of an inverter, which was developed at UVEE. The principle of function and circuit implementation of a single-phase inventer, various calculations (design of an LC filter, DC link capacitor, semiconductor elements and heat sink) are described in the thesis. A design of fast overcurrent protections, oscillator and saw signal generator is included. Furthermore, a printed circuit board was designed which was optimized by thermal simulation in the Workbench Ansys. Subsequently, the printed circuit board was mounted, debugged and verification measurements were performed on it. At the end of the thesis there is a documentation for the implemented equipment.
Description
Keywords
Střídač, H-můstek, LC-filtr, MOSFET, pulsně šířková modulace, oscilátor s Wienovým článkem, rychlá nadproudová ochrana, návrh DPS, Maxwell Ansys, oteplovací zkouška, měření účinnosti., Inverter, H-bridge, LC-filter, MOSFET, pulse width modulation, Wien bridge oscillator, fast overcurrent protection, Maxwell Ansys, temperature test, efficiency measurement.
Citation
SMOLÁK, M. Jednofázový střídač s výstupními parametry 230 V / 50 Hz / 100 VA [online]. Brno: Vysoké učení technické v Brně. Fakulta elektrotechniky a komunikačních technologií. 2019.
Document type
Document version
Date of access to the full text
Language of document
cs
Study field
Silnoproudá elektrotechnika a výkonová elektronika
Comittee
doc. Ing. Pavel Vorel, Ph.D. (předseda)
doc. Ing. Radoslav Cipín, Ph.D. (místopředseda)
Ing. Dalibor Červinka, Ph.D. (člen)
doc. Ing. Bohuslav Bušov, CSc. (člen)
doc. Ing. František Veselka, CSc. (člen)
Ing. Jan Martiš, Ph.D. (člen)
Ing. Petr Huták, Ph.D. (člen)
Date of acceptance
2019-06-05
Defence
Student seznámil komisi se svou diplomovou prací. Prezentoval postup návrhu, realizaci a testování vyrobeného zařízení. Dále student zodpověděl otázky oponenta a vhodně reagoval a další otázky komise.
Result of defence
práce byla úspěšně obhájena
Document licence
Standardní licenční smlouva - přístup k plnému textu bez omezení